技术资料联轴器选择和程序
如果您想查看选择程序和注意事项，请转到以下步骤。
如果您希望缩小产品系列范围或进行初步选择，
单击此处。
如果您已经决定了使用条件并希望进行详细的选择，
单击此处。
夹爪式挠性联轴器L系列选型
- （1）选择时，根据发动机类型和运行条件，从表1中选择使用系数。
- （2）将负载扭矩（T）乘以表 1 中的使用系数（SF）来计算修正扭矩（T'），并选择型号，使联轴器的允许扭矩等于或大于修正扭矩（见下表）。
- (3)请确认所需轴孔直径在选定型号的最大轴孔直径以下。超过的情况下，请选择适合那个的型号。(参照下表)
- (4)直接连接电机使用时，请参照表2、表3的选择表。
扭矩计算方法
T = 9550 × P n T = 974 × P n
- T=负荷扭矩N・m{kgf・m}
- P=传输功率kW
- n = 转速r/min
- T' = 修正扭矩 N・m {kgf・m}
| 负载性质 | 发动机的种类 | ||
|---|---|---|---|
| 电动机涡轮机 | 汽油发动机 柴油发动机 (6缸以上) |
汽油发动机 柴油发动机 (不足6气缸) |
|
|
·无负载时间，均匀 ·无正反运行 ·运行时间=8小时左右/天 ·以低扭矩启动 |
1.0 | 1.5 | 2.0 |
|
·中度负荷波动 ·中等冲击载荷 ·运行时间=8小时左右/天 ·无正反运行 (适用于一般驱动的SF) |
1.5 | 2.0 | 2.5 |
|
·有剧烈冲击负荷 ·负载波动大 ·运行时间=8小时左右/天 ·有正反运行 ·启动扭矩大 |
2.0 | 2.5 | 3.0 |
*如果每天的营业时间为 16 至 24 小时，则使用系数增加一级。
| 50Hz 电机 额定输出功率 kW |
2极 3000 r/min | 4极 1500 r/min | 6极 1000 r/min | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 电机 轴径 mm |
电机 额定扭矩 N・m {kgf・m} |
使用系数 | 电机 轴径 mm |
电机 额定扭矩 N・m {kgf・m} |
使用系数 | 电机 轴径 mm |
电机 额定扭矩 N・m {kgf・m} |
使用系数 | |||||||
| 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | |||||||
| 联轴器型号 | 联轴器型号 | 联轴器型号 | |||||||||||||
| 0.1 | 11 | 0.6 {0.06} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
||||||||||
| 0.2 | 11 | 0.6 {0.06} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
11 | 1.3 {0.13} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 1.9 {0.19} |
L050-S L050A-S |
L050-S L050A-S |
L070-S L070A-S |
| 0.4 | 14 | 1.3 {0.13} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 2.5 {0.26} |
L050-S L050A-S |
L050-H L070A-S |
L050-H L075A-S |
19 | 3.8 {0.39} |
L070-S L070A-S |
L075-S L075A-S |
L075-S L075A-S |
| 0.75 | 19 | 2.4 {0.24} |
L070-S L070A-S |
L070-S L070A-S |
L070-S L070A-S |
19 | 4.8 {0.49} |
L070-S L070A-S |
L070-M L075A-S |
L070-H L075A-S |
24 | 7.2 {0.73} |
L075-S L075A-S |
L075-S L075A-S |
L075-M L090A-S |
| 1.5 | 24 | 4.8 {0.49} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
24 | 9.5 {0.97} |
L075-S L075A-S |
L075-M L090A-S |
L075-H L095A-S |
28 | 14.7 {1.5} |
L090-S L090A-S |
L090-M L095A-S |
L090-H L100A-S |
| 2.2 | 24 | 7.0 {0.71} |
L075-S L075A-S |
L075-S L075A-S |
L075-M L090A-S |
28 | 14.0 {1.43} |
L090-S L090A-S |
L090-M L095A-S |
L090-H L100A-S |
28 | 20.6 {2.1} |
L095-S L095A-S |
L099-S L100A-S |
L099-M L100A-S |
| 3.7 | 28 | 11.8 {1.2} |
L090-S L090A-S |
L090-M L095A-S |
L090-M L095A-S |
28 | 23.5 {2.4} |
L095-S L095A-S |
L090-H L100A-S |
L090-H L100A-S |
38 | 35.3 {3.6} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 5.5 | 38 | 17.6 {1.8} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 35.3 {3.6} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 52.9 {5.4} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 7.5 | 38 | 23.5 {2.4} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 48.0 {4.9} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 71.5 {7.3} |
L110-S L110A-S |
L110-S L110A-S |
L110-H |
| 11 | 42 | 35.3 {3.6} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 69.6 {7.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-H | 42 | 105 {10.7} |
L110-S L110A-S |
L150-M | L150-M |
| 15 | 42 | 48.0 {4.9} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 95.1 {9.7} |
L110-S L110A-S |
L110-H | L110-H | 48 | 143 {14.6} |
L190-S | L190-M | L190-M |
| 18.5 | 42 | 58.8 {6.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-M | 48 | 118 {12.0} |
L150-S | L150-S | L150-H | 55 | 176 {18.0} |
L190-S | L190-M | L190-H |
| 22 | 48 | 69.6 {7.1} |
L110-S L110A-S |
L110-S L110A-S |
L150-S | 48 | 140 {14.3} |
L150-S | L150-M | L150-H | 55 | 210 {21.4} |
L225-S | L225-M | L225-H |
| 30 | 55 | 95.1 {9.7} |
L190-S | L190-S | L190-S | 55 | 191 {19.5} |
L190-S | L190-M | L190-H | 60 | 286 {29.2} |
L225-M | L225-H | L225-H |
| 37 | 55 | 118 {12.0} |
L190-S | L190-S | L190-M | 60 | 235 {24.0} |
L225-S | L225-M | L225-H | |||||
| 45 | 55 | 143 {14.6} |
L190-S | L190-M | L190-M | 60 | 286 {29.2} |
L225-H | L225-H | L225-H | |||||
| 55 | 55 | 175 {17.9} |
L190-S | L190-M | L190-H | ||||||||||
| 75 | 55 | 239 {24.4} |
L190-M | L190-H | L190-H | ||||||||||
| 90 | 55 | 286 {29.2} |
L190-M | L190-H | L190-H | ||||||||||
| 110 | 55 | 350 {35.7} |
L190-H | L190-H | L225-H | ||||||||||
| 132 | 55 | 420 {42.9} |
L190-H | L225-H | |||||||||||
- 注)1.选择时请确认电机的特性。
- 注)2. 标记为附带标准轴孔加工的轮毂库存。
| 60Hz 电机 额定输出 kW |
2极 3600 r/min | 4极 1800 r/min | 6极 1200 r/min | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 电机 轴径 mm |
电机 额定扭矩 N・m {kgf・m} |
使用系数 | 电机 轴径 mm |
电机 额定扭矩 N・m {kgf・m} |
使用系数 | 电机 轴径 mm |
电机 额定扭矩 N・m {kgf・m} |
使用系数 | |||||||
| 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | 1.0 | 1.5 | 2.0 | |||||||
| 联轴器型号 | 联轴器型号 | 联轴器型号 | |||||||||||||
| 0.1 | 11 | 0.5 {0.05} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
||||||||||
| 0.2 | 11 | 0.5 {0.05} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
11 | 1.0 {0.1} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 1.6 {0.16} |
L050-S L050A-S |
L050-S L050A-S |
L050-H L070A-S |
| 0.4 | 14 | 1.0 {0.1} |
L050-S L050A-S |
L050-S L050A-S |
L050-S L050A-S |
14 | 2.0 {0.2} |
L050-S L050A-S |
L050-S L050A-S |
L050-H L070A-S |
19 | 2.9 {0.3} |
L070-S L070A-S |
L070-S L070A-S |
L075-S L075A-S |
| 0.75 | 19 | 2.0 {0.2} |
L070-S L070A-S |
L070-S L070A-S |
L070-S L070A-S |
19 | 3.9 {0.4} |
L070-S L070A-S |
L070-M L075A-S |
L070-H L075A-S |
24 | 5.9 {0.6} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
| 1.5 | 24 | 3.9 {0.4} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
24 | 7.8 {0.8} |
L075-S L075A-S |
L075-S L075A-S |
L075-H L090A-S |
28 | 11.8 {1.2} |
L090-S L090A-S |
L090-M L095A-S |
L090-M L095A-S |
| 2.2 | 24 | 5.9 {0.6} |
L075-S L075A-S |
L075-S L075A-S |
L075-S L075A-S |
28 | 11.8 {1.2} |
L090-S L090A-S |
L090-M L095A-S |
L090-M L095A-S |
28 | 17.6 {1.8} |
L090-M L095A-S |
L090-H L100A-S |
L090-H L100A-S |
| 3.7 | 28 | 9.8 {1.0} |
L090-S L090A-S |
L090-S L090A-S |
L090-M L095A-S |
28 | 19.6 {2.0} |
L090-M L095A-S |
L090-H L100A-S |
L090-H L100A-S |
38 | 29.4 {3.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 5.5 | 38 | 14.7 {1.5} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 29.4 {3.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 44.1 {4.5} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
| 7.5 | 38 | 19.6 {2.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
38 | 40.2 {4.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 59.8 {6.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-M |
| 11 | 42 | 29.4 {3.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 58.8 {6.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-M | 42 | 87.2 {8.9} |
L110-S L110A-S |
L110-M | L110-H |
| 15 | 42 | 40.1 {4.1} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
42 | 79.4 {8.1} |
L110-S L110A-S |
L110-M | L110-H | 48 | 120 {12.2} |
L150-S | L150-M | L150-H |
| 18.5 | 42 | 49.0 {5.0} |
L110-S L110A-S |
L110-S L110A-S |
L110-S L110A-S |
48 | 98.0 {10.0} |
L110-S L110A-S |
L150-S | L150-M | 55 | 147 {15.0} |
L190-S | L190-M | L190-H |
| 22 | 48 | 58.8 {6.0} |
L110-S L110A-S |
L110-S L110A-S |
L150-S | 48 | 117 {11.9} |
L150-S | L150-M | L150-H | 55 | 175 {17.9} |
L225-S | L225-S | L225-M |
| 30 | 55 | 79.4 {8.1} |
L190-S | L190-S | L190-S | 55 | 159 {16.2} |
L190-S | L190-M | L190-H | 60 | 239 {24.4} |
L225-S | L225-M | L225-H |
| 37 | 55 | 98.0 {10.0} |
L190-S | L190-S | L190-S | 60 | 196 {20.0} |
L225-S | L225-M | L225-M | |||||
| 45 | 55 | 120 {12.2} |
L190-S | L190-S | L190-M | 60 | 239 {24.4} |
L225-S | L225-M | L225-H | |||||
| 55 | 55 | 146 {14.9} |
L190-S | L190-M | L190-H | ||||||||||
| 75 | 55 | 199 {20.3} |
L190-M | L190-H | L190-H | ||||||||||
| 90 | 55 | 239 {24.4} |
L190-M | L190-H | L190-H | ||||||||||
| 110 | 55 | 292 {29.8} |
L190-H | L190-H | L225-H | ||||||||||
| 132 | 55 | 350 {35.7} |
L190-H | L190-H | L225-H | ||||||||||
- 注)1.选择时请确认电机的特性。
- 注)2. 标记为附带标准轴孔加工的轮毂库存。
